Oversized Planter

Laura Alviso

6 years ago

Just in time for you christmas front porch decorating! I am ready to style my front porch and make it a christmas wonderland! Thank you to Massca for Sponsoring me to create this amazing planter!

PROJECT NAME: Oversized planter box

SKILL LEVEL: Intermediate

FINISHED DIMENSIONS:

12 ¾” wide (square) x 50” tall

*Dimensions are subject to change based on the space requirements.

MATERIALS:

11/32 Cat Ps1-09 Square Structural Douglas Fir Sanded Plywood, Application as 4 x 8
2-in x 3-in x 96-in Whitewood Stud
Wood glue
Wood Filler
Paint or Stain of your chose
1-in x 4-in x 8-ft Square Primed Pine Board
Sand paper 180g/220g
Nails (for your nail gun or ones to hammer)

TOOLS USED:

Massca Pro Aluminum Pocket Hole Jig System M1 | Bundle
Drill
Pocket Hole screws
Clamp
Sander
Nail Gun
Compressor or Hammer (depending on your method)

Project Plans can be downloaded here!

Project Plans

Step 1: Cut all pieces to lumber cut list size. Project Plans can be downloaded here!

Step 2: Take board (A), (B), (C) once cut and create pocket holes. When cutting pocket holds, I used the Massca Pro Aluminum Pocket Hole Jig System M1 | Bundle. First, you will want find the thickness. In this case I am using a 2×3 stud, so I would then use the depth of 1-1/2”. Using the Massca depth gauge, adjust the collar to the correct depth. You can do this by attaching the drill bit to the drill then inserting it into the hole in the jig. Reach the depth gauge. Once tight you are ready to start creating the holes.

Step 3: For (A), (B), drill through the Stud using the Pocket Hole Jig, horizontally creating about 4 to 5 pocket holes going in one direction as show on the drawn image. On the same side as the horizontal holes, turn the stud to a vertical position. Then pocket hole the bottom end.

Step 4: Add one pocket hole on either end of (B), in the direction of the arrows. This creates a U shape. Then add 1-1/4” countersunk wood screws and wood glue.

Step 5: Once both U shape supports are made now is the time to assemble. Grab the outsides shown in Figure B. Take one of the four pieces, glue and then screw through the pocket holes to secure to outside piece. Secure U shape 1 inch lower than the top. 1-1/2” countersunk wood screws and wood glue.

Step 6: Then add the other U Shape to the other side of that board.

Step 7: Then add side piece to the other side. Creating a box with two sides left to add.

Step 8: Slip in one side at a time and secure using a nail gun and glue. Since we have the main support structure, flip and add the other side.

Step 9: Now that we have our overall shape. Lets add the top trim. Work your way around one piece at a time. Secure with glue and nail gun. This trim will sit about 3” above the top edge.

Step 10: Now that we are all put together, wood fill all nail holes on exterior and any spots you don’t feel are perfect. Allow to dry.

Step 11: Now that the wood filler is dry, take the Orbit Sander and sand the entire surface of the planter until everything is smooth to your desired feel.

TIP: If you have any gaps between the wood and you don’t have wood filler, fill the gaps with wood glue and pat saw dust into the glue, covering it entirely. Once the glue dries (about 20mins), sand the area to remove any excess glue and sawdust.

Step 12: If you plan to stain: Using a rag, dip it into the wood conditioner and apply an even coat to the entire surface of the beam. Allow to dry for 20 minutes. We chose to paint! In this case, paint a primer and then follow with white exterior paint.

Step 13: Apply one coat of desired stain or paint and allow to dry.

Step 14: Its done! Now stand back and admire your work!